About Us

Most states call for 100 amps minimum, but with all the new electronic devices, air conditioning and electric heat, I would suggest 200 amps especially in new homes. This gives you space for future additions. This is not a job for an unlicensed person to attempt. In most cases it involves replacing everything from the service loop (this is the wire that extends from the top of your meter to the utility tie in) up to and including the main panel.

GFCI stands for Ground Fault Circuit Interrupt. GFCIs protect any appliance plugged into it and can also be wired to protect other outlets that are connected to it. There are two types of GFCIs in homes, the GFCI outlet and the GFCI circuit breaker. Both do the same job, but each has different applications and limitations.

The GFCI outlet is a replacement for a standard electrical outlet. A GFCI is not dependent of a ground to function. It does not measure shorts to the ground, it measures the current difference between the hot and neutral wires. A sudden difference of 5 ma. or more, indicating that there is another path for the electricity to flow through will trip this device. The only downside to this is there may be some nuisance tripping in highly inductive loads like large motors or even fluorescent lamps or fixtures on the same circuit. But the newer models seemed to have corrected this somewhat.

Any bathroom or garage outlet within 6' of a sink must be GFCI protected. The code also requires all kitchen outlets for countertop use to be GFCI protected. GFCI outlets must be installed in any area where electricity and water may come into contact, including basements, pools, spas, utility rooms, attached garages and outdoors. At least one GFCI outlet is required in an unfinished basement and for most outdoor outlets.

The GFCI circuit breaker controls an entire circuit, and is installed as a replacement for a circuit breaker on your home's main circuit board. Rather than install multiple GFCI outlets, one GFCI circuit breaker can protect the entire circuit. There is a test button and a reset button on these units. If you press the test button the reset should pop out. To reset just push the reset button in.

It is not a good idea to put lights on GFCI protected circuits, so you are not left in the dark if the circuit trips. Generally, equipment such as refrigerators, freezers and sump pumps that cannot go without electrical power for an extended period without causing costly losses or property damage should not be placed on a GFCI protected circuit. GFCIs are very sensitive and are subject to nuisance tripping. GFCI receptacles do not last outdoors even under the best of conditions. Be sure to test the device using the "test" button before you use one.

At the present time most states allow you to do whatever you want in your own home. But doing electrical work yourself is a gamble. How much are you willing to risk to save money? There is a reason why it takes years of training to become an electrician. Do not make a mistake by taking electricity lightly, even the smallest job could be a safety hazard. Why take a chance? Get a licensed Electrical Contractor to do the work.

Also, in some states the homeowner can pull his own Electrical permit for work in his single-family home. What he does not know, is that in case of damage or fire caused by his work, his homeowners’ insurance will not pay. The homeowners’ insurance will only cover the damage if the work is done by a licensed Electrical Contractor. You should check with your homeowners Insurance before you pull a permit.

The most dangerous time is when you tell yourself: this is easy, I can do it myself. Why should I get an electrician? Then when you don't remember where all those wires went, or your hair is standing straight up, you will say to yourself, “Well maybe I better call someone to straighten up this mess.” This will end up costing you double what you thought you were going to pay.

In every kitchen, family room, dining room, living room, parlor, library, den, bedroom, or area of dwelling, receptacle outlets shall be installed so that no point along the floor line in any wall space there is more than six feet, from an outlet in that space. This spacing is to prevent the use of extension cords. Outlets are usually placed about 18 inches above floor level. Switches usually go about 48 inches from floor level. For convenience, outlets each single receptacle in a single branch circuit is usually configured for 1.5 amps, duplex outlets for 3amps in estimating total amperage for that circuit. Air conditioners should be on a single dedicated circuit.

All 15 and 20 amp receptacles installed within 6 feet of a kitchen sink or wet bar shall have GFCI protection. Receptacles in a kitchen used to serve counter tops should be supplied with at least two 20 amp branch circuits, for small appliances. Each fixed appliance (refrigerator, stove, dishwasher) shall have its own dedicated circuit. On countertops 12 inches or wider a receptacle shall be installed so that there is no more than 24 inches between outlets. Receptacles outlets installed to serve island countertops shall be installed above, or within 12 inches below the countertop. There shall be no more than 24 inches from center line of countertop. No receptacle shall be installed face up on a sink countertop.

The AFCI (Arc Fault Circuit Interrupter) breaker, will shut off a circuit in a fraction of a second if arcing develops. The current inside of an arc is not always high enough to trip a regular breaker. You must have noticed a cut or worn piece of a cord or a loose connection in a junction box or receptacle arcing and burnt without tripping the regular breaker. As you can guess this is a major cause of fires in a dwelling.

There is a difference between AFCIs and GFCIs. AFCIs are intended to reduce the likelihood of fire caused by electrical arcing faults; whereas GFCIs are personnel protection intended to reduce the likelihood of electric shock hazard. Do not misunderstand, GFCIs are still needed and save a lot of lives.

Combination devices that include both AFCI and GFCI protection in one unit will become available soon. AFCIs can be installed in any 15 or 20 ampere branch circuit in homes today and are currently available as circuit breakers with built-in AFCI features.

If a GFCI receptacle is installed on the load side of an AFCI it is possible for both the AFCI and the GFCI to trip on a fault if the current exceeds the limit for both devices. It is also possible for the AFCI to trip and the GFCI to not trip since the two devices could race each other. However, in no case is safety compromised.

Starting January 1, 2002, The National Electrical Code, Section 210-12, requires that all branch circuits supplying 125V, single phase, 15 and 20 ampere outlets installed in dwelling bedrooms be protected by an AFCI. Eventually they will be in more areas, but the NEC selected to require them on bedroom circuits first because a CPSC study showed many home fire deaths were related to bedroom circuits.